Examinando por Autor "Palomino, Carlos"

Mostrando 1 - 3 de 3

Boosting the activity of UiO-66(Zr) by defect engineering: efficient aldol condensation of furfural and MIBK for the production of bio jet-fuel precursors
(Royal Society of Chemistry, 2024-05-30) Sanz, María; Leo, Pedro; Palomino, Carlos; Paniagua, Marta; Morales, Gabriel; Melero, Juan A.
The production of jet-fuel precursors from furfural via aldol-condensation with methyl-isobutyl ketone (MIBK) over defect-engineered UiO-66(Zr) catalysts is presented. The catalysts are prepared using formic acid (FA), trifluoroacetic acid (TFA) and HCl as synthesis modulators, leading to the incorporation of defects on the microcrystalline structure of the metalorganic framework (MOF) material, which dramatically boosts the catalytic performance. An extensive characterization of the modified catalysts by means of X-ray diffraction (XRD), argon adsorption isotherm, thermogravimetry (TGA), transmission electron microscopy, and FTIR spectroscopy of adsorbed acetonitrile, confirmed the incorporation of missing-linker and missing-node defects within the MOF structure, enabling the explanation of the enhancement in the catalytic process. The analysis of the reaction kinetics evidences that, working under moderate temperature conditions, conversion of furfural and selectivity to the desired adduct (FuMe) close to 100% can be achieved, avoiding the formation of degradation and bulkier compounds. Finally, despite the generation of defects within the UiO-66(Zr) structure, the resultant catalyst displays good reusability in low furfural concentration mediums.
Catalytic activity and stability of sulfonic-functionalized UiO-66 and MIL-101 materials in friedel-crafts acylation reaction
(Elsevier, 2022-05-01) Leo, Pedro; Crespí, Neus; Palomino, Carlos; Martín, Antonio; Orcajo, Gisela; Calleja, Guillermo; Martínez, Fernando
Sulfonic-containing UiO-66 and MIL-101 MOF materials, prepared by direct synthesis with a sulfonic acid-including benzene dicarboxylate (SO3H-BDC) linker, have been evaluated as acid catalysts in Friedel–Crafts acylation of anisole with acetic anhydride. The catalytic activity of these materials was compared to other conventional acidic sulfonic heterogeneous catalysts, such as commercial Nafion-SAC-13 and Amberlyst-15. The catalytic performance of MOF materials was significantly dependent on their textural properties and the availability of sulphonic acid groups. MIL-101-SO3H material displayed a remarkable anisole conversion and specific activity per sulfonic acid centre due to its open structure and multimodal pore size distribution. The inherent properties of MIL-101-SO3H material allowed a more sustainable catalyst regeneration than those used for conventional heterogeneous catalysts due to the deposition of reagents and products, in particular poly-acetylated compounds. MIL-101-SO3H proved an easy recovery and reusability in successive runs without any loss of activity. These promising results evidenced the potential of MIL-101-SO3H as an alternative catalyst for acid-catalyzed reactions.
Catalytical advantages of Hf-MOFs in benzaldehyde acetalization
(Elsevier, 2024-05-15) García-Rojas, Elena; Tapiador, Jesús; Leo, Pedro; Palomino, Carlos; Martos, Carmen; Orcajo, Gisela
The potential use of acetals as bioadditives based on sustainable feedstocks in the automotive industry is of great interest. If such feedstock is a residual stream, the process would represent a dual environmental challenge, such as the valorization of glycerol obtained as a by-product of biodiesel to produce acetals. There are just scarce works about this synthetic route due to the challenge in finding efficient catalytic converters for glycerol valorization in a single process. Herein four different Metal-Organic Frameworks (MOFs) are evaluated as heterogeneous catalysts for the acetalization reaction of benzaldehyde with methanol, specifically, two structures, MOF-808 and UiO-66, containing two structural metal ions, zirconium and hafnium. The aim of this work is to investigate the influence of the MOF structure, the metallic active sites and the reaction conditions on the catalytic performance of this acetal production-type reaction. Furthermore, the recyclability of the catalyst is evaluated, and a potential reaction mechanism is suggested. As relevant results, Hf-MOFs showed higher benzaldehyde conversion than Zr-based ones, and significant improvements in reaction conditions were achieved, such as a significant reduction in catalyst loading of 99.6 % using UiO-66-Hf, and an optimization of reagent ratios reducing methanol consumption by 50 % for a 92 % of benzaldehyde conversion. The Brønsted character of UiO-66-Hf seems to enhance the reaction rate more than the metal center accessibility and larger pore volumes offered by MOF-808